Journal of the European Optical Society - Rapid publications, Vol 11 (2016)

Controlling the optical creation of gold nanoparticles in a PVA matrix by direct laser writing

T. Ritacco, L. Ricciardi, M. La Deda, M. Giocondo

Abstract


We report about the study on the physical features of gold nano-particles (GNPs) created by 2-photons photo-reduction Direct Laser Writing in a Poly-Vinyl Alcohol (PVA) matrix doped with HAuCl4. We drop cast a film of the PVA+ HAuCl4 onto a glass substrate, in which we create 1D gratings made by stripes of GNPs with a single laser sweep. We show that the stripe width increases with the laser power and the exposure time. We also analyse the influence of the exposure time over the created nano-particles size distribution and density and we show that by suitably adjusting the exposure time it is possible to maximize the frequency of a given diameter. By comparing the experimental results with a polymerization “voxel†model, we are able to evaluate the effective cross section for 2- photons absorption of our material.

© The Authors. All rights reserved. [DOI: 10.2971/jeos.2016.16008]

Full Text: PDF

Citation Details


Cite this article

References


S. Engelhardt, ”Direct Laser Writing,” in Laser Technology in Biomimetics, V. Schmidt, and M. R. Belegratis, eds., 13–56 (Springer-Verlag, Berlin/Heidelberg, 2013).

M. Roehrig, M. Thiel, M. Worgull, and H. Hölscher, ”3D Direct Laser Writing of Nano- and Microstructured Hierarchical GeckoMimicking Surfaces,” Small 8(19), 3009–3015 (2012).

W. Barthlott, T. Schimmel, S. Wiersch, K. Koch, M. Brede, M. Barczewski , S. Walheim, et al., ”The Salvinia Paradox: Superhydrophobic Surfaces with Hydrophilic Pins for Air Retention Under Water,” Adv. Mater. 22 (21), 2325–2328 (2010).

T. Bueckmann, N. Stenger, M. Kadic, J. Kaschke, A. Frölich, T. Kennerknecht, C. Eberl, et al., ”Tailored 3D Mechanical Metamaterials Made by Dip-in Direct-Laser-Writing Optical Lithography,” Adv. Mater. 24(20), 2710–2714 (2012).

L. Yuan, M. L. Ng, and P. R. Herman, ”Femtosecond laser writing of phase-tuned volume gratings for symmetry control in 3D photonic crystal holographic lithography,” Optical Materials Express 5(3), 515–529 (2015).

T. Ergin, N. Stenger, P. Brenner, J. Pendry, and M. Wegener, ”ThreeDimensional Invisibility Cloak at Optical Wavelengths,” Science 328, 337–339 (2010).

B. Richter, T. Pauloehrl, J. Kaschke, D. Fichtner, J. Fischer, A. M.Greiner, D. Wedlich, et al, ”Three-Dimensional Microscaffolds Exhibiting Spatially Resolved Surface Chemistry,” Adv. Mater. 25(42), 6117–6122 (2013).

M. Infusino, A. De Luca, A. Veltri, A. Veltri, C. Vazquez-Vazquez, M. A. Correa-Duarte, R. Dhama, et al., ”Loss-Mitigated Collective Resonances in Gain-Assisted Plasmonic Mesocapsules,” ACS Photonics 1(4), 371–376 (2014).

K. Kaneko, H. B. Sun, X. M. Duan, and S. Kawata, ”Two-photon photoreduction of metallic nanoparticle gratings in a polymer matrix,” Appl. Phys. Lett. 83(7), 1426–1428 (2003).

R. Kuladeep, L. Jyothi, S. Chakradhar, and D. N. Rao, ”Fabrication of metal nanostructures in a polymer matrix using femtosecond laser writing technique,” Opt. Eng. 53(7), 071823 (2014).

M. Sakamoto, M. Fujistuka, and T. Majima, ”Light as a construction tool of metal nanoparticles: Synthesis and mechanism,” J. Photoch. Photobio. C 10, 33–56 (2009).

W. M. Huang, and J. L. Shi, ”Synthesis and properties of ZrO(2) films dispersed with Au nanoparticles,” J. Sol-Gel Sci. Techn. 20, 145–151 (2001).

R. Zanella, and C. Louis, ”Influence of the conditions of thermal treatments and of storage on the size of the gold particles in Au/TiO2 samples,” Catal. Today 107(8), 768–777 (2005).

M. I. A. Umar, C. C. Yap, R. Awang, A. A. Umar, M. M. Salleh, and M. Yahaya, ”Formation of gold-coated multilayer graphene via thermal reduction,” Mater. Lett. 106, 200–203 (2013).

S. Passinger, Two-Photon Polymerization and Application to Surface Plasmon Polaritons (Cuvillier Verlag, Göttingen, 2008).


Journal of the European Optical Society:Rapid publications - ISSN 1990-2573. JEOS:RP is subject to the EOS General Terms and Conditions.